fs it4 manual

Otherwise, it would causeFS-lT4SIt is compatible with carsThe AFHDS 2A (Automatic Frequency Hopping Digital System Second Generation) developed andOffering superior protectionFLYSKY's AFHDS technology is considered to be one of the leaders in the RC market today. Bidirectional Communication. Capable of sending and receiving data, each transmitter is capable of receiving dataSupport. Multi-channel Hopping Frequency. This systems bandwidth ranges from 2.4055GHz to 2.475GHz. This band is divided inOmni-directional Gain Antenna. The high efficiency Omni-directional high gain antenna cuts down on interference, whileUnique ID Recognition System. Each transmitter and receiver has it's own unique ID. Once the transmitter and receiverLow Power Consumption. The system is built using highly sensitive low power consumption components,Antenna. StylusSw3. Sw1. PowerPrecautions:Never grip the transmitter antenna when operating a model. It significantly degrades the RF signalThe FS-iT4S has two main control inputs, the wheel and trigger.Trigger: Used for acceleration, breaking and reverse.FS-lT4SThe status indicator is used to indicate the power and working status of the transmitter.Blue light: the transmitter is on and working. Flashing: the transmitter is binding.There are 4 trims affecting surface functionality, one for throttle, steering, reverse and. Each time a trim isIt is possible to make quicker trim adjustments by holding the trim inWhen the trim position reaches the middle, the transmitter beeps in a higher tone.Attention. For best signal quality, ensure that the receiver is mounted away from motorsThe status indicator is used to indicate the power status of the receiver.Lit in red: the receiver is on and working. Flashing quickly: the receiver is binding. Flashing slowly: the bound transmitter is off.The connectors are used to connect the parts of model and the receiver.Before operation, install the battery and connect the system as instructed below.

• flysky fs-it4 manual pdf, flysky fs-it4 manual, fs it4 manual.

Digital proportional radio control systemRead this manual carefully before operation in order to ensure your safety, and the safety of others or theIf you encounter any problem during use, refer to this manual first. If the problem persists, contact yourFS-lT4S. Table of contentsAppendix 1 FCC Statement.34FS-lT4SPay close attention to the following symbols and their meanings. Failure to follow these warnings couldDanger. Not following these instructions may lead to serious injuries or death. Warning. Not following these instructions may lead to major injuries. Not following these instructions may lead to minor injuries.Prohibited. Mandatory. Do not fly at night or in bad weather like rain or thunderstorm. It can causeDo not use the product when the visibility is limited. Do not use the product on rainy or snowy days. Should any type of moistureInterference could cause loss of control. To ensure the safety of you and others,Do not use this product when you are tired, uncomfortable, or under theIt may cause serious injury to yourself as well asThe 2.4GHz radio band is completely different from the previously used lowerNever grip the transmitter antenna when operating a model. It significantlyDo not touch any part of the model that generates heat during operating orThese parts mayMisuse of this product can lead to serious injuries or death. To ensure the safetyMake sure the product is properly installed in your model. Failure to do so mayMake sure to disconnect the receiver battery before turning off the transmitter. Failure to do so may lead to unintended operation and cause an accident. Ensure that all motors operate in the correct direction. If not, adjust theMake sure the model flies within a certain distance.

The home screen diplays useful information about you're model, including sensors, current activeModel Name. Transmitter Battery. Receiver Signal. Receiver Battery. Sensor Feedback. Break Mixing. Throttle Curve. MixesEngine Cut. Sound. Throttle Idle. Steering Position. Throttle Position. Channel 3. Channel 4. Boat Mode. Throttle Trim Position. Steering Trim. Help. Menu. The system's navagation is designed to be easy and quick, using both a stylus and fingers.To enter a function touch its corrasponding icon. Navagate functions by swiping up and down toTo go back to a previous menu press the. Icon.FS-lT4SThe Reverse function is used to correct a servo or motor'sFor example if aTo fix this all weEnd points are the limits of the servos range of movement. There are 2 endpoints per channel, one is theTo select an endpoint move the desired control surface in theThe currently selected endpointOnce you have choosen an endpoint, touch the channel youAt the top the current channel, selected endpoint andThe endpoints location is also shown asTo edit an endpoint's value drag the wheel at the bottom of theSubtrim changes the center point of the channel, for example if a car's wheels are slightly out of alignmentTo set the subtrim function:Use the wheel at the bottom of the screen to change the value, a real time readout of the channelsThe sub trim has a value representing the current subtrim setting, followed by a graphic representation ofBelow the graphic there is a real time read out of the channels current position.To restore the entire function to default, select the reset icon in the channel selection menu. Channel List. Subtrim setting and channel's current positionThis function changes the response curve of the steering, there are 2 main parameters:Rate cannot be more than 100%. Exp.

Only use specified battery. Do not open, disassemble, or attempt to repair the battery. Do not expose to excessive heat or liquids. Follow the steps to install the transmitter battery:Insert a fully-charged battery into the compartment. Make sure that the battery makes good contactReplace the battery compartment cover.Connect the receiver and the servos as indicated below. Switch (Optional). BatteryBatServos. ReceiverAfter setting up, follow the instructions below to operate the system.Follow the steps below to turn on the system:Hold the power button until screen lights up. Connect the receiver power supply. The system is start now. Operate with caution, or serious injury could result.The transmitter and receiver have been pre-bound before delivery. If you are using another transmitter orConnect the power to any of the CH1 to CH4 connectors. The indicator will start to flash, indicatingOnce the binding isIf anything is doesn't work as expected, restart this procedureBefore operation, perform the following steps to check the system:Check operating distance distance: one operator holds the transmitter, and another one moves theCheck the model and mark the distance from where the modelDanger. Stop operation if any abnormal activity is observed. Danger. Make sure the model flies within the safe distance.FS-lT4SThe position of the wheel can be adjusted to be more comfortable to use.Grab the plastic underneath the wheel. (Do not pull the wheel itself as this could lead to long termDefault Position. Fully ExtendedIt is possible to adjust the stiffness so that the position of the wheel is easier or harder to move. To do thisTrims allow you to change the centre point of the steering, throttle, channel 3 and 4. An good example ofThe System has 3 trim switches located behind the steering wheel.Follow the steps below to turn off the system:Slide the power switch of the transmitter down to the OFF position. DangerOr it may lead to unintended operation and cause an accident.

This function can set a “dead zone” for their throttle control, this means that the throttle will notIt is also possible to set up the initial amount of throttle that willTo set the throttle neutral:To setup the dead zone select the dead zone option at the left side of the screen, and use the wheelThe current percentage will be shown above theForward. Once finished setting up these functions, press the back icon located at the bottom right of the screen toFS-lT4SThis function has two variables:The maximum is 100%. To reset this function select the standard steering mix from the functions main menu.This function is used to add a curve to the throttle response, meaning that the throttle will respondTo activate thisThis function has 5 points that can be edited. To select a point simply touch the corresponding number (LOnce a point is selected use the wheel at the bottom of the screen to change its value, all changes will beTo reset this function press the reset icon located at the middle bottom of the screen.This function must be active to work, if the icon at the bottom left corner is not showing a tick, select it. When a tick is shown the function is active. As a square wave, the peaks representing break on,and the drops break reduction. Trigger point: Changes the point in which the A.B.S. will kick in. The trigger point is represented as a whiteBreak return. Controls the amount the break will back off from full break, if set to 50Here the pulses are shown as a square wave, the peaks being break on,As the break return function isTo edit this function simply use the wheel to change its value, as theBelow the graph is a bar thatDelay. This determines how long it takes for the A.B.S. system to take effect. AtA.B.S. to kick in. Cycle length. Increases or decreases the time between pulses, in this menu the A.B.S.FS-lT4S. Trigger point. Changes the point in which the A.B.S. will kick in.

: Changes the steering curve, which changes he response of the steering wheel, the exp settingChanges to the rate and exponential can be seen on the graph locatedChanges to the rate and exponential can be seen on the graph, locatedThe system also gives a real-time readout ofNote. The system gives a real time readout of the channels position, not theBy changing the steering curve we can make the wheel more or lessExponential 100%. This function must be set as active before use, to activate the functionFS-lT4STo restore the entire function to default, select the reset icon located at the bottom center of the screen. To restore the entire function to default, select the reset icon located at the bottom center of the screen. Exponential 0%. Rate 64%This function changes the speed in which the steering travels, if the cars wheels are turning too fast, itThis function is also used to simulate a realistic for scale models. There are two variables. Turn Speed: Sets how quickly the wheels turn from their starting position, to the position the systemsReturn Speed: Sets how quickly the wheels turn back to their center position. To set the steering speed:To restore the entire function to default, select the reset icon located at the bottom center of the screen.This function changes which wheels are involved in steering, front, rear, or 4 wheel steering. To enable thisRear side: Rear wheel steering. Same phase: Front and rear steering at the same time,Rev. phase (Reverse Phase): The front wheels and backTo set the steering mix. Select the desired method of steering, the system shows a preview of the steering method on theTo reset this function, select the reset icon located at the bottom middle of the screen.

When checked, the receiver only outputs PPM on CH1 output, however PPM is capable of transferring allTo enable PPM touch the box in this menu. When the box is checked the PPM is active.FS-lT4SMonitors the receiver battery voltage. Use the supplied battery’s user manual to set the lower andSetting the voltage alarm sets a custom low battery level alarm. To change settings, touch the desired value and move the wheel to set theLow voltage: This sets your batteries default low voltage value is 4.00V. Alarm voltage: Sets the low voltage alarm. High voltage: Set the maximum voltage when the battery is full. TheWhen checked, an alam will be triggered if the receiver's packet error rate rises above 60%.This function is used to protect models and users if the receiver loses signal and therefor is no longerTo set a failsafe position select a channel and select the icon at the bottomTo set the value, move your channel to the desired position, for exampleOnce the failsafe has been set the value will show up in the failsafe channelThis function displays current active sensors. The type of sensor is displayed on the left hand side, its ID in the middle and the sensors output on theUnder “Type”, and the sensors output on the right under “Value”. All sensors have numerical IDAt the bottom of the list this menu has an error rate display, this is a good indicator of signal quality.The main screen can display the value of up to 4 sensors, this function selects which sensors are displayed. First select a slot, any sensors that are connected will automatically populate this list, select the desiredThere are 2 types of sensors, basic and advanced. A basic sensors only reports back 1 value, but anThis function allows the user to monitor the models RPM and how far it has traveled. If the sensor appears in the menu, it means that there is one connected.Selects the desired sensor. Set rotation lengt.

When attaching a speed sensor to a wheel etc, it is important that the sensor knows exactly how farThe system uses this distance to calculate distance traveled. Odometer 1. Records the distance traveled during a session. (Note: Restarting the system will also reset odometer 1). Odometer 2. Records the total distance traveled since last reset. This means that the distance over several sessionsReset odometer 1: Resets odometer 1 to 0. Reset odometer 2: Resets odometer 2 to 0.FS-lT4SAfter connecting the i-Bus module to your receiver and servos, select steering, throttle, channel 3 or 4. Locate the desired servo, and using the tool provided to push the channels button on the i-Bus module.Some types of servo will require a different frequency to function properly, to change this value simplyConsult your servos user manual to find out the correct frequency. Note. The most common frequency is 50Hz.The range test function is useful for finding out if there are sources of interference nearby. To preform a range test pair the RX and TX, then open this function. Press SW2 (Located near your smallThe blacklight timeout function controls how long the system will wait before turning off screensNote. Backlight time can affect the battery life of your system, the longer the time, the shorter the battery willTo change the backlight time enter the function and select the desired time from the list.This function controls the backlight brightness. (Note: Increasing the brightness will reduce battery life). To change the backlight brightness, use the wheel at the bottom of the screen to change the percentage.Toggles all system sounds (excluding alarms). To disable the system sounds uncheck the box by touching it.Toggles all alarm sounds. To disable the alarm sounds uncheck the box by touching it.The auto power off function powers off the system automaticly after 2 min, unless a receiver is connected. To enable this function check the box by touching it.

The trigger point isTo change the position of theThe higher the percentage the more the trigger has to be moved in orderDuty cycle. Changes the length of each pulse and the gap between them, asChanges to the wave form are shown in real time on the graph. Steering mix. When turning A.B.S. can become a problem for some models, thisTo have constant breaking unless turning simply move the wheel the opposite direction so that theTo change this function simply use the wheel to take it from it’s off position, and apply a percentage ofThe graph will show the results real-time, also when the trigger is moved the results will be show on theThis function changes how quickly the throttle will react, both when pressed and released. This is usefulThere are 2 main settings in this function:Return: How quickly the throttle backs off. To adjust these settings, select the desired setting and use the wheel toThe bar in the middle ofFS-lT4SThis function changes the midpoint of the throttle, this could be used in aTo change the midpoint, use the wheel at the bottom of the screen, theThis function is used for models that use a fuel based engine, if left at 0To combat this idle up makes sure that theThen use the wheel at the bottom of theThrottle cut is used for fuel based models and is used to cut the throttle, essentially cutting the engine. To edit the settings move the wheel at the bottom of the screen. When active the function will stop theFor help setting up your model's engine consult the model'sThis function is used only when you are using a model boat. When using this function the breakThis function enables you to use models that require more than oneIf your model uses extra channels for braking, each channel can beThis function is used to create a mix between channels and control methods. For example if at lowerIt is possible to have up to 4 mixes.Next select a slave.

A slaves may only be output channels, however this also includes any unused auxEach curve mix can independently be signed to a toggle using theThis function displays the models channel output and can be used toTo toggle this function press the icon at the bottom center of the screen.The race timer has 4 modes:Down timer: Counts down from the set time. Lap timer: Keeps track time for each individual lap. Lap memory: Records the results from the lap timer. To reset press the rest icon.This function assigns the systems physical buttons to different functions. To assign a function to a key select the key from the diagram, then select aTo set the keys function:Scroll down the list until you find the function you wish to assign andOnce the selection has been made the function will automaticallyThe models function is used to change between, copy and delete model setups. The FS-iT4S can store upSelecting a model. To select a model touch the select model menu, once in the menu touch the name of the model to load it. Reset Model. To reset (delete model by resetting to default), first select a model fromNaming Models. To name a model, fist select a model from the model selection menu (asOnce you have finished entering in the name using the keyboard press theCopy ModelCopy source. This is the model you wish to copy. Copy Target. This is the model you wish to overwrite.This function enables you to bind the RX and TX so that no other system may interfere with your modelsTo bind the transmitter with a receiver:On the TX select “Bind with a receiver”. Once the RX and TX are bound the TX will exit this menu automatically (Unless using a 1-wayThis menu allows you to change the communication protocol for the TX,AFHDS 2A 2-Way. Note. AFHDS 2A 2-Way is the latest, most stable and advanced communicationWhen changing mode you will be prompted to confirm.

If the touch screen is not functioning correctly, use this function to recalibrate. To recalibrate once inside the function touch the centre of the crosses as they appear on the screen. TheNote. It is recommended that you use the supplied stylus.FS-lT4SUse this function to change between Metric and Imperial mesurement systems.The system can be used with various computer based simulators via USB. To enable the simulator functionConnecting PC charging and upgrade the firmware, USB data transmission will not workThe internal software of the transmitter can be updated using the USB interface connected to a PCTo avoid any loss of controlA confirmation is requested. When the firmware is updating, never disconnect the USB cable or remove the battery or the transmitterThis function can be helpful only when connected with computer. Follow the steps as shown below:Connect a transmitter with a computer by USB cable. Enter transmitter firmware upgrade menu and press OK to complete.Channels. Model type. SensitivityWhen lower than 3.7 V. Steering Range. Throttle Range. WeightDimension (Length x Width x Height)Power inputColor. CertificateChannel bandwidthBandRF powerRF mode. AFHDS 2A (Second generation automatic frequency hoppingCode typeChannels. Model type. RF rangeBandReceiver sensitivityWeightDimension (Length x Width x Height)Power inputOutput. CertificateFS-lT4S. Appendix 1 FCC Statement. This equipment has been tested and found to comply with the limits for a Class B digital device pursuantThese limits are designed to provide reasonable protection against harmfulThis equipment generates, uses and can radiate radio frequencyHowever, there is no guarantee that interference will not occur in a particularIncrease the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver isTo assure continued compliance, any changes or modifications not expressly approved by the partyThis equipment complies with Part 15 of the FCC Rules. Operation is subject to the following twoCaution! The manufacturer is not responsible for any radio or TV interference caused by unauthorizedSuch modifications could void the user authority to operate theChanges or modifications not expressly approved by the party responsible forEU Statement. Hereby, FLYSKY RC MODEL TECHNOLOGY CO., LTD, declares that this FSIT4 is in compliance with the essential requirements and other relevant provisionsPDF Version: 1.4. Linearized: No. XMP Toolkit: 3.1-701. Creator Tool: Adobe InDesign CS6 (Windows). Instance ID: uuid:224db71e-1326-4768-893a-50b36071ab6a. Original Document ID: xmp.did:EBF258E2AD05E511ABF58C2D1F6D131F. Document ID: xmp.id:B667466DAC2EE511AA8FF12B0B8CE83C. Rendition Class: proof:pdf. Derived From Instance ID: xmp.iid:B02EEA67AC2EE511AA8FF12B0B8CE83C. Derived From Document ID: xmp.did:E251B23B332CE5119B9380071FBE3DAB. Derived From Original Document ID: xmp.did:EBF258E2AD05E511ABF58C2D1F6D131F. Derived From Rendition Class: default. History Action: converted. History Software Agent: Adobe InDesign CS6 (Windows). Producer: Adobe PDF Library 10.0.1. Trapped: False. Has XFA: No. Page Count: 36. Creator: Adobe InDesign CS6 (Windows). FLYSKY (FS-GT3C-GR3F) 3CH 2.4 GHz Surface Transmitter with GR3F Receiver. GT3C merupakan bentuk penyempuranaan dari GT3B secara design kita sudah.FlySky FS-B800 3.7V 800mAh Lipo Battery For FS-GT3C FS-GT2B F04629. FLYSKY (FS-GT3C-GR3F) 3CH 2.4 GHz Surface Transmitter with GR3F Receiver. I have purchased this to use on small depron airplane with Turnigy 9Xv2. English, German, Spanish, Italian, French, Portuguese, Russian,. 2.4g Flysky FS-GT3C 3CH Transmitter Controller GR3C Receiver For RC Car RC Boat.

HeliPal is famous for their Fast Shipping, Low Price. 42 items. FlySky FS-i6 2.4G 6CH AFHDS RC Transmitter With FS-iA6 Receiver for UAV. Flysky FS-GT3B 2.4G 3CH Gun RC System Transmitter with Receiver For.Reload to refresh your session. Reload to refresh your session. Please try your search again later.Running a Blackout xbe proA diode can lower voltage by.7 volt or you can make a voltage divider with resistors if you felt like soldering. Will it have the range?Theoretically this is possible but the range will not be largeThe Flysky manual that has the receiver and transmitter. Lots of places to download the manual. Just search flysky manuals. The t6 is older protocol. Ive been using this radio for close to two years.Also there haven't been any issues posted other then the screen being a tad hard to view under direct sunlight. Is a very reasonable price radio.Ive been using this radio for close to two years.Also there haven't been any issues posted other then the screen being a tad hard to view under direct sunlight. Is a very reasonable price radio. Ive been using this radio for close to two years.Also there haven't been any issues posted other then the screen being a tad hard to view under direct sunlight. Is a very reasonable price radio. Maybe YOU haven't had problems, but there's been plenty others who have. Using your arguement, I could say there's no problems with this new FlySky radio since I haven't had any problems, when we both know that's not true.I purchased the system from myrcmart and received the radio in approx 10days. This radio was purchased for use in my VTA touring car. Here are my observations: -Wheel needs more tension for my taste in on road carpet racing. Maybe I can replace the tension spring and bearings while I am in there. Have not seen anybody do this yet. -The quick switches on the handle needed to be set to none as an option. Hitting these while racing caused some less than desirable results. -The touch screen works good.

-I love the power off F1 engine scream. Maybe with future firmware hacks a small block V8 sound can be added. -Plan on using the temp sensor tomorrow to get real time motor temps. This should be more accurate than taking the temp after the race. -Compared to my M11 Airtronics this flysky is a featherweight. This will get replaced. -I charge the radio with my HTC charger. The output amps are under the max rating of the flysky battery. -The orange chrome model matches my Xray T3 chassis pretty well. More observations to come.If so, how does it work. They don't come with any reflective stickers like my speky did for its rpm sensor.Shipped with a FS-SPD01 Magnetic. No magnet include with sensor. The Instruction Manual shows how to install on page 12. -magnet can be placed on inside of wheel rim -sensor can be placed on other side of wheel (beyond tire) THe manual shows it does not require a very close proximity of sensor to magnet. Hope that's true. Have not tried it yet. I've wondered if it can work with the magnet in a CY magneto (rotor)?That silver colored reflective tape sold in bicycle shops might work with an optical tach. I have a hand held optical tach and the reflective material it shipped with looked very similar to bicycle safety tape.That silver colored reflective tape sold in bicycle shops might work with an optical tach. I have a hand held optical tach and the reflective material it shipped with looked very similar to bicycle safety tape. Maybe I can use my old speky rpm sensor sticker.Maybe I can use my old speky rpm sensor sticker. Better if it can attach and detect magnetic field change from motor like Yeah Racing sensors for MT4 - SPD02 uses optical detection, no high expectation - the temp.Better if it can attach and detect magnetic field change from motor like Yeah Racing sensors for MT4 - SPD02 uses optical detection, no high expectation - the temp.It was nice just to have some information on the unit. Please give more details when you can.

The FS-iT4 is holding solid connections at over 0.5 mile. For once I'm glad I was one of the first to try something 'cause usually I won't ever jump in early. So far, FlySky has exceeded my expectations.Use of this site indicates your consent to the Terms of Use. Use of this site indicates your consent to the Terms of Use.